GUIDE
How do the quote, design approval and handover of a vehicle wrap work?
The steps of a vehicle wrap from asking for a quote to collecting the vehicle. What a quote needs, how to compare two quotes, what to check at handover.
Written by Erdem G. · İZVELA
Ordering a vehicle wrap is less like buying vinyl and more like turning a vehicle into a readable advertising surface. Measurement, design and workmanship depend on each other. When one slips, the result shows at the first wash or in the first summer. Below we answer, in order, the questions a business asks when it wraps a vehicle for the first time. Film types and care are covered on the service page. Here the focus is the order of the job and what to look at in each step.
Which steps does a vehicle wrap go through?
The job runs in six steps. First the details of the vehicle are gathered for the quote. Then the vehicle is seen and measured at the survey. The third step is design, and approval is given on a photograph of the vehicle itself. After approval the film is printed and cut. The application is done in an enclosed workshop. The last step is the handover check.
When the order breaks, the next step pays for it. A design prepared before the measurements lands on a door handle or a window line on application day. Printing that starts before approval has to be printed again when a change is requested.
What information should you give when asking for a quote?
The first condition of an accurate quote is the identity of the vehicle. Make, model and model year separate the bodies of two vehicles sold under the same name. Whether a van has a long or short wheelbase, whether the side door slides and whether the rear door is one piece or a pair of wings all change the area to be covered.
The second piece of information is the scope. Do you want lettering on the sides only, a partial wrap or the whole vehicle? If you have not decided yet, saying so is useful too. The scope is settled together at the survey.
The third is a few photographs of the vehicle taken from all four sides. A photograph does not replace measurement, but it lets the survey start prepared. If the paint has scratches, dents or an area that was repaired before, show that as well. Film does not hide a paint defect. It sits on top of it and can make it more visible.
If you have the vector file of your logo, send it with the request. On a vehicle the letters grow to the size of a metre or more. A small image that looks sharp on a phone breaks up at its edges at that size.
How do you compare two quotes?
In vehicle wrap quotes the price difference usually comes from a difference in scope. Two quotes can only be set side by side when they describe the same job. To see this, check whether a few lines are written in the quote.
The first line is the brand and grade of the film. “Quality film” tells you nothing. The quote should name which manufacturer’s product will be used, because the life of a film does not show on the first day.
The second line is the list of surfaces to be covered. “The sides” can leave open whether the sliding door and the rear door are included. Then look at the detail work. Will the door handles and mirrors be removed so the film can be tucked under them, or will the film be cut around them? Where nothing is removed, the cut edges lift over time. Part of the gap between two quotes comes from here.
Finally, ask whether design is included and what happens if a problem comes from the application. Workmanship faults such as bubbling or lifting at the edge are kept apart from outside causes such as an accident or a scratch. When that line is drawn at the start, there is nothing to argue about later.
What should you check when approving the design?
A design should be approved on a photograph of your own vehicle, not on a blank background. At İZVELA the design is shown placed on a photograph of the customer’s vehicle. A flat drawing does not show whether the lettering falls on a door seam or on the fuel cap.
Look at the approval image first as if you were seeing the vehicle from across the street. Can you read the business name and the phone number from a distance? Then look closely. Check whether any line of text is cut by a door handle, a window line or a panel gap. A letter that falls on a seam cannot be fixed on application day.
The two sides of a vehicle are not symmetrical. One side may have the sliding door and the other the fuel cap. Ask to see each side on its own. Approval given on one side can bring a surprise on the other.
Raise any change at the approval stage. A change made before printing only affects the design file. A change requested after printing means the film is printed again.
What should be ready before application day?
Empty the vehicle and plan the day you will be without it around your work. On fleet jobs the vehicles are taken in one after another. Deciding in advance which vehicle goes on which day keeps your field schedule intact.
If the vehicle carries old film, lettering or stickers, mention it at the quote stage. Removing an old application is a separate job and adds to the time.
Noting the existing scratches and dents together when you hand the vehicle over protects both sides. The application is done in an enclosed workshop. Film does not settle properly in dust and wind. When it is applied in the street or in an open car park, dust stays under the film and bubbles form.
What should you check when you collect the vehicle?
Look at the vehicle in daylight, first from a little distance and then up close. There should be no bubbles on the surface and no specks of dust trapped under the film.
Look at the edges. The film should be folded in over the panel edges, with no loose corner standing off the surface. Door handles, mirrors and the area around the lights are where workmanship shows most. Check whether the film has been pressed into the gaps between panels. Film that bridges a gap bursts in the first few washes.
Then compare the vehicle with the approval image. The position of the lettering and the colours should match what you approved. Read the phone number once more, digit by digit. A single wrong digit wipes out the advertising value of the whole vehicle.
The rules for washing and cleaning are explained to you at handover. A fault noticed on handover day is put right in the workshop that same day. A fault noticed on the road means taking the vehicle off work once more.
Can we wrap a vehicle if we do not have a logo?
You can, but the order changes. The design on a vehicle starts from the logo, and without one the identity work comes first. Once a logo is drawn, the same file is used on the sign, the business card and social media too. A logo drawn in a hurry for a vehicle ends up being a logo that has to be replaced everywhere later.
Who removes the old film from the vehicle?
We do the removal as well. Old film comes off with the help of heat, the leftover adhesive is cleaned and the new application goes onto a clean surface. If you know how long the old application has been on the vehicle, tell us. Film that has spent years in the sun comes off in pieces and removal takes longer.
What should we do if we see an edge lifting after the application?
Let us know without waiting. Lifting caught early is fixed on a single edge. Left alone, water and dirt get under the edge and that area may need to be covered again. We fix lifting that comes from the application.

